Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a big resurgence throughout the nation, Gentle Giant desires to make sure that these traditional, beautiful devices remain damage-free while being transported. Oh, and we desire the people moving them to be safe, too.

At first look, pinball machines can appear daunting to move due to the fact that of their weight, size, and fragility. The good news is, our competent Giants have a couple of tricks up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox

The bulk of modern pinballs (made in the last Twenty Years approximately) have a hinge system which allows the headbox to be folded down. Early pinball devices had their headboxes bolted on, utilizing either two or four bolts. All Electro-Mechanical pinballs utilize this system, along with the early Solid State makers.

Later devices have hinges and utilize a locking system to keep the headbox upright. There may likewise be 2 bolts inside as added safety, in case the lock is broken or accidentally un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball devices, you require to remove the headbox rear access panel to get to the bolts and plugs within. Usually this panel has a lock on it to keep it in location, however over time the key might have been lost. On a regular basis, there is a screw keeping this panel in location.

As soon as inside, eliminate the bolts and disconnect the big connectors that have electrical wiring decreasing into the maker. You may wish to identify these adapters to put them back in the right spot, however they need to be different sizes, making it challenging to plug back improperly.

You can now get rid of the headbox completely, or fold the headbox down onto the playfield glass. Ensure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will help keep the back glass in place.
Early Solid State Pinballs

For early Strong State Pinballs, you will have to remove the back glass. There is a lock located on the headbox in one of 3 areas: the left-hand side at the top, right-hand side at the top or on top of the headbox in the.

Once unlocked, get rid of the back glass by raising it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.

Then, open the back box light panel by raising the latch located on either the left-hand side or right-hand side. The panel can now swing out towards you, and give you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to raise up the light panel in order to swing it open.

Now that you are inside, you can remove the bolts, and any plugs that have wires going down into the device. You might desire to label these plugs to put them back in the right spot. You might not have to get rid of the plugs, as the wiring ought to be long enough to enable the headbox to be folded down.

At this moment, you can secure the lamp panel and replace the back glass.
Modern Solid State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable lock system situated at the back of the headbox. Utilizing the provided key, turn the latch 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can easily unlatch the back box at the back of the device. This is a basic setup and needs no tools.

If you can now fold down the head box onto the cabinet, you're done. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.

You need to get inside if you can not fold the head box down. There is a lock situated at the top of the back glass in the. Utilize the provided key to unlock, and remove the back glass by lifting it up from the bottom, and after that pulling it out from the bottom.

Next, you will need to remove the screen panel. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later on Sega browse this site and Stern pinballs utilize a fluorescent tube for the back glass lighting).

Get rid of the 2 bolts, put the back box back together, and fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.
Removing the Legs.

Pinball Device legs are held in location by 8 bolts. They will be either 5/8 inch or 9/16 inch heads. The contemporary pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be gotten rid of, and the legs will come off.

These captive nuts and threaded plates can be damaged, and the use of extra nuts may have been required. If this holds true, you will have to open the front door of the pinball, slide out the playfield glass, and raise the playfield.

With the front door (coin door) open, move the lock down bar lock throughout and get rid of the lock down Source bar. Then move out the playfield glass, and put in a safe location. Next, raise up the playfield by positioning your hand where the ball drains pipes, and raise the playfield up.

You need to now have access to any nuts that might have been check over here utilized. As soon as any nuts have actually been removed, replace the playfield glass and lock down bar, and lock the front door.

Be sure to mark or remember which legs are for the front and back, as they will be adjusted differently to suit.
Loading the Pinball.

You are now ready to transport your pinball machine. Before you load it, make sure you remove the pinballs so they don't bounce around during transport.

If you are moving the pinball using a van or SUV, it may be easier to remove the legs just prior to filling the maker. Get a good friend to assist and have one of you supporting the pinball, while the other eliminates the front legs.

Ensure you strap the pinball in, as you do not desire it moving if you have to stop all of a sudden!

For Electro-Mechanical pinball devices, you need to remove the headbox rear access panel to gain access to the bolts and plugs within. (Some more recent Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).

If you are moving the pinball using a van or SUV, it may be easier to remove the legs just prior to loading the maker. Get a friend to have and assist one of you supporting the pinball, while the other gets rid of the front legs.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Tips From the Moving Company Pros: Ways To Move a Pinball Maker”

Leave a Reply

Gravatar